MD0: Difference between revisions

From SNAKE WIKI
 
No edit summary
Line 18: Line 18:
{{MD0_Guides}}
{{MD0_Guides}}
{{Note|info|Standalone ECUs do not required any modifications.}}
{{Note|info|Standalone ECUs do not required any modifications.}}
==Device Configuration==
{{Note|warn|Updating. Back to the page later.}}


==Installation==
==Installation==
Line 54: Line 57:


==Bluetooth Connection==
==Bluetooth Connection==
{{Note|reminder|For easy setup, [[MD0|SNAKE MINI DIZZY]] has a built-in Bluetooth and a PC Service Tool.}}
{{Note|reminder|[[MD0|SNAKE MINI DIZZY]] has a built-in Bluetooth and a PC Service Tool.}}
[[File:MD0_Bluetooth_01.jpg|thumb|right|Pairing a new Device]]
[[File:MD0_Bluetooth_01.jpg|thumb|right|Pairing a new Device]]
'''Pairing a new Device'''<br/>
'''Pairing a new Device'''<br/>
Line 72: Line 75:
You'll see a message '''Waiting for Device No xxx'''.
You'll see a message '''Waiting for Device No xxx'''.
{{Note|info|If you need to connect to another device, just press the button with the Bluetooth icon. The Service Tool will remove the paired device and start searching for available ones.}}
{{Note|info|If you need to connect to another device, just press the button with the Bluetooth icon. The Service Tool will remove the paired device and start searching for available ones.}}
<br clear=all>
==Configuration==
{{Note|reminder|By default, for safety reasons, the device is shipped in transport mode with the ignition coils turned off.}}
[[File:MD0_Tool_Engine.jpg|thumb|right|Engine Parameters]]
'''Engine Parameters'''<br/>
To activate the ignition coils, you must configure some engine parameters:
*Engine model.
*Mounting point on the cylinder head.
First, pick your engine model from the list. Then, use '''<''' and '''>''' buttons to select one of the three mounting points on the cylinder head, where you fix the [[MD0|SNAKE MINI DIZZY]].<br/>
Apply the settings by pressing the '''Set Base Angle''' button.
{{Note|info|If your engine is not on the list, you can use the learning procedure to set up the [[MD0|SNAKE MINI DIZZY]]}}
<br clear=all>
[[File:MD0_Tool_Timing.jpg|thumb|right|Ignition Timing]]
'''Ignition Timing'''<br/>
After setting up the engine parameters, it's recommended to fine-tune the ignition using a timing light.<br/>
*Start the engine and allow it to warm up
*Short the Service Check Connector with a jumper wire.
*Connect a timing light to the #1 Coil and point it toward the pointer on the timing belt cover.
*Adjust ignition timing, if necessary, using '''+1''', '''-1''' and '''+0.1''', '''-0.1''' buttons
{{Note|warn|Changes will be applied immediately with each press of the buttons}}
<br clear=all>
[[File:MD0_Tool_SparkMode.jpg|thumb|right|Spark Mode]]
'''Spark Mode'''<br/>
Select your preferred Coils control mode:<br/>
'''Sequential Mode''' (Default)<br/>
This mode is standard in Honda OEM ECUs.<br/>
Each coil fires once per cylinder, enhancing coil longevity and keeping them cooler.
'''Wasted Spark Mode'''<br/>
This is what a lot of aftermarket sport ECUs use.<br/>
Two coils work as a pair, cleaning fuel residue from cylinders during the exhaust cycle. Ideal for maintaining engine efficiency in boosted setups running rich.
{{Note|error|Using aftermarket or race coils in wasted spark mode without external fused power can damage your engine wiring.}}
<br clear=all>
[[File:MD0_Tool_Security.jpg|thumb|right|Security Options]]
'''Security Options'''<br/>
Secure your device against unauthorized connections. Set up a PIN code for authentication.
<br clear=all>
[[File:MD0_Tool_Update.jpg|thumb|right|Update Firmware]]
'''Update Firmware'''<br/>
Keep your firmware up to date.
<br clear=all>
<br clear=all>

Revision as of 20:16, 15 October 2024

SNAKE MINI DIZZY

Description

The world's smallest device designed to completely remove the OEM distributor and convert to Individual Coils.

Despite the age of Honda's "Distributor Era" engines (B, D, F and H series), they are still very popular in the tuning community. A significant drawback of these older engines is the distributor ignition system, which includes a high-voltage section and “temperamental” VR sensors.

Our Device eliminates these shortcomings, enhancing engine performance and reliability.

Compatible with OEM and Standalone ECUs.


Advantages

  • Improved ignition timing precision up to 0.1 deg at 14000 RPM.
  • Better spark energy without the inefficiencies of a traditional distributor system.
  • Easy Setup via Bluetooth Connection.
  • Less cluttered engine compartment, making maintenance and modifications easier.
  • Compatible with OEM and Standalone ECUs.

Plug Types

Depending of the year of production here are three different types of the Distributor plug(s).

ECU Modification

OEM ECUs must be modified to Accept Low Voltage Signals. See guides below.

Most Popular ECU Guides

Search Guide by Car Model

90-93 Honda Accord 4.

93-97 Honda Accord 5. USA Spec.

93-97 Honda Accord 5. EUR Spec.

98-02 Honda Accord 6. USA Spec.

98-02 Honda Accord 6. EURO Spec.

92-95 Honda Civic 5

94-01 Honda Civic 5.5. UK Spec.

96-00 Honda Civic 6.

95-01 Honda CR-V 1.

92-98 Honda CR-X DelSol.

92-97 Honda Domani.

89-93 Honda Integra 2.

93-01 Honda Integra 3.

92-96 Honda Prelude 4.

96-01 Honda Prelude 5.

95-99 Rover 400 Series. (D16 Engine)

99-05 Rover 45 Series (D16 Engine)

Search Guide by ECU Hardware

OBD1 ECU Families

OBD2A ECU Families

OBD2B ECU Families

Standalone ECUs do not required any modifications.

Device Configuration

Updating. Back to the page later.

Installation

STEP 1: Remove OEM Distributor

STEP 1: Remove OEM Distributor

  • Disconnect Connector(s) from the distributor
  • Disconnect the plug wires from the cap
  • Remove the distributor mounting bolts
  • Remove distributor from cylinder head.


STEP 2: Remove following parts from the Distributor

STEP 2: Remove following parts from the Distributor

  • Coupling
  • Pin
  • Pin retainer


STEP 3: Install Coupling to Device

STEP 3: Install Coupling to Device

  • Install Coupling to the shaft.
  • Align the index mark of shaft and coupling.
  • Drive in the pin
  • Secure it with the pin retainer


STEP 4: Install Device to cylinder head

STEP 4: Install Device to cylinder head

  • Coat O-Ring with engine oil
  • Align offset of the lugs on the end of Device and its mating grooves in the Camshaft.
  • Slip Device into position
  • Install and tighten one mounting bolt (any desired mounting point)
  • Install Coils and Wiring
  • Connect Connector(s) to Device


Bluetooth Connection

SNAKE MINI DIZZY has a built-in Bluetooth and a PC Service Tool.
Pairing a new Device

Pairing a new Device
When connecting to the device for the first time, connection must be configured. Follow this simple steps:

  • Turn ON the Ignition.
  • Make sure your PC's Bluetooth is active.
  • Start Snake MD0 Tool
  • You will see a message Searching Devices....
  • Wait about 10 seconds, Service Tool will automatically found the device and setup the connection.
  • Finally you will see the Serial Number of the connected device SnakeMD0-SPP[xxx]



Connect to the Paired Device

Connect to the Paired Device
After the first connection, Service Tool will automatically reconnect to the paired device.
You'll see a message Waiting for Device No xxx.

If you need to connect to another device, just press the button with the Bluetooth icon. The Service Tool will remove the paired device and start searching for available ones.