MD0: Difference between revisions

From SNAKE WIKI
No edit summary
No edit summary
 
Line 17: Line 17:
{{Note|warn|OEM ECUs must be modified to [[MD0_TECH|Accept Low Voltage Signals]]. See guides below.}}
{{Note|warn|OEM ECUs must be modified to [[MD0_TECH|Accept Low Voltage Signals]]. See guides below.}}
{{MD0_Guides}}
{{MD0_Guides}}
{{Note|info|Standalone ECUs do not required any modifications.}}


==Device Configuration==
==Device Configuration==
{{Note|warn|Updating. Back to the page later.}}
{{Note|warn|Before installation [[MD0|SNAKE MINI DIZZY]] must be configured to match your engine model.}}
[[File:MD0_Configure_01.png|center|Before installation [[MD0|SNAKE MINI DIZZY]] must be configured to match your engine model.]]


==Installation==
==Installation==
Line 33: Line 33:
[[File:MD0_Install_02_Remove_Parts.jpg|thumb|right|STEP 2: Remove following parts from the Distributor]]
[[File:MD0_Install_02_Remove_Parts.jpg|thumb|right|STEP 2: Remove following parts from the Distributor]]
'''STEP 2: Remove following parts from the Distributor'''
'''STEP 2: Remove following parts from the Distributor'''
*Thrust washer
*Coupling
*Coupling
*Pin
*Pin
Line 48: Line 49:
[[File:MD0_Install_04_Install_Device.jpg|thumb|right|STEP 4: Install Device to cylinder head]]
[[File:MD0_Install_04_Install_Device.jpg|thumb|right|STEP 4: Install Device to cylinder head]]
'''STEP 4: Install Device to cylinder head'''
'''STEP 4: Install Device to cylinder head'''
*Coat O-Ring with engine oil
*Coat O-Ring with engine oil.
*Align offset of the lugs on the end of Device and its mating grooves in the Camshaft.
*Align offset of the lugs on the end of Device and its mating grooves in the Camshaft.
*Slip Device into position
*Slip Device into position.
*Install and tighten one mounting bolt (any desired mounting point)
*Install and tighten one mounting bolt.
*Install Coils and Wiring
*Install Coils and Wiring.
*Connect Connector(s) to Device
*Connect Connector(s) to Device.
<br clear=all>
<br clear=all>


Latest revision as of 20:44, 15 October 2024

SNAKE MINI DIZZY

Description

The world's smallest device designed to completely remove the OEM distributor and convert to Individual Coils.

Despite the age of Honda's "Distributor Era" engines (B, D, F and H series), they are still very popular in the tuning community. A significant drawback of these older engines is the distributor ignition system, which includes a high-voltage section and “temperamental” VR sensors.

Our Device eliminates these shortcomings, enhancing engine performance and reliability.

Compatible with OEM and Standalone ECUs.


Advantages

  • Improved ignition timing precision up to 0.1 deg at 14000 RPM.
  • Better spark energy without the inefficiencies of a traditional distributor system.
  • Easy Setup via Bluetooth Connection.
  • Less cluttered engine compartment, making maintenance and modifications easier.
  • Compatible with OEM and Standalone ECUs.

Plug Types

Depending of the year of production here are three different types of the Distributor plug(s).
  • OBD1 Type Plug

    OBD1 Type Plug

  • OBD2A Type Plug

    OBD2A Type Plug

  • OBD2B Type Plug

    OBD2B Type Plug

ECU Modification

OEM ECUs must be modified to Accept Low Voltage Signals. See guides below.

Most Popular ECU Guides

Search Guide by Car Model

90-93 Honda Accord 4.

93-97 Honda Accord 5. USA Spec.

93-97 Honda Accord 5. EUR Spec.

98-02 Honda Accord 6. USA Spec.

98-02 Honda Accord 6. EURO Spec.

92-95 Honda Civic 5

94-01 Honda Civic 5.5. UK Spec.

96-00 Honda Civic 6.

95-01 Honda CR-V 1.

92-98 Honda CR-X DelSol.

92-97 Honda Domani.

89-93 Honda Integra 2.

93-01 Honda Integra 3.

92-96 Honda Prelude 4.

96-01 Honda Prelude 5.

95-99 Rover 400 Series. (D16 Engine)

99-05 Rover 45 Series (D16 Engine)

Search Guide by ECU Hardware

OBD1 ECU Families

OBD2A ECU Families

OBD2B ECU Families

Device Configuration

Before installation SNAKE MINI DIZZY must be configured to match your engine model.
Before installation SNAKE MINI DIZZY must be configured to match your engine model.

Installation

STEP 1: Remove OEM Distributor

STEP 1: Remove OEM Distributor

  • Disconnect Connector(s) from the distributor
  • Disconnect the plug wires from the cap
  • Remove the distributor mounting bolts
  • Remove distributor from cylinder head.


STEP 2: Remove following parts from the Distributor

STEP 2: Remove following parts from the Distributor

  • Thrust washer
  • Coupling
  • Pin
  • Pin retainer


STEP 3: Install Coupling to Device

STEP 3: Install Coupling to Device

  • Install Coupling to the shaft.
  • Align the index mark of shaft and coupling.
  • Drive in the pin
  • Secure it with the pin retainer


STEP 4: Install Device to cylinder head

STEP 4: Install Device to cylinder head

  • Coat O-Ring with engine oil.
  • Align offset of the lugs on the end of Device and its mating grooves in the Camshaft.
  • Slip Device into position.
  • Install and tighten one mounting bolt.
  • Install Coils and Wiring.
  • Connect Connector(s) to Device.


Bluetooth Connection

SNAKE MINI DIZZY has a built-in Bluetooth and a PC Service Tool.
Pairing a new Device

Pairing a new Device
When connecting to the device for the first time, connection must be configured. Follow this simple steps:

  • Turn ON the Ignition.
  • Make sure your PC's Bluetooth is active.
  • Start Snake MD0 Tool
  • You will see a message Searching Devices....
  • Wait about 10 seconds, Service Tool will automatically found the device and setup the connection.
  • Finally you will see the Serial Number of the connected device SnakeMD0-SPP[xxx]



Connect to the Paired Device

Connect to the Paired Device
After the first connection, Service Tool will automatically reconnect to the paired device.
You'll see a message Waiting for Device No xxx.

If you need to connect to another device, just press the button with the Bluetooth icon. The Service Tool will remove the paired device and start searching for available ones.


Retrieved from "https://snaketuning.com/mediawiki/index.php?title=MD0&oldid=637"